Clock Repair FAQ & Care Tips

Answers on winding, striking, oiling, cuckoo clocks, wooden movements and grandfather clock setup, from Cape Town clock repairers.

These are the questions we get asked most often. If yours isn’t here, call us.

Quotes and
ollection

No. If you have a grandfather clock, we’ll come to you. For a mantel clock, wall clock or cuckoo clock, bring it in for a free assessment and quotation.

We offer free pickup in our local area. We collect the clock and service it in our workshop, because that’s where it can be done properly. We don’t service clocks in the home, apart from the odd adjustment to the beat or rate.

Winding, running and stopping

You can’t over-wind a spring-driven clock. Once it’s fully wound it simply won’t take any more, and forcing it past that point can break something. Some weight-driven clocks may be an exception. If a fully wound clock won’t run, it has a mechanical problem that needs attention. It isn’t wound too tight.

This is common in spring-driven clocks. A spring delivers less power as it runs down, so anything that makes the clock work harder than it should will stop it before the spring is spent. The usual causes are lack of oil, built-up dirt and worn pivot holes (the bearings). Springs can also tire over the years and no longer give a full 8-day run. All of this can be put right. If the spring is weak, the simplest fix is often to wind the clock twice a week.

There’s always a reason, even if it isn’t obvious. If it always stops at the same time, the minute hand may be catching the hour hand. It could also be out of beat or standing on an uneven surface. Worn parts, a bent tooth on a wheel or a badly adjusted escapement can cause it too. Also check that the clock is still going after you’ve wound it, because some clocks like to stop right then.

If it keeps happening, the movement usually needs to be taken apart, cleaned and inspected, with the pivots serviced and any worn parts replaced. Most stopping problems disappear after that, but tracking down an intermittent fault does take time.

Striking and
chiming

Most clocks use a count wheel to decide how many times to strike. The time side and the strike side of the movement work independently. The time side doesn’t tell the strike side what the time is, only that it’s time to strike again. So the two can drift apart. Either the strike didn’t run when it should have and fell behind, or it didn’t stop when it should have and got ahead.

The most common cause is that the strike side wasn’t wound, or wasn’t wound fully. Worn parts, poor lubrication and bad adjustment can also stop the strike from running or stop it from stopping. Getting it back in step depends on the clock, so call us if you’d like help. If it keeps going out of step for no obvious reason, the clock needs servicing.

Several things can cause this, sometimes in combination. Turning the hands backward past 12:00 is a frequent one. Loose, bent or badly fitted hands can make it look as if the strike is off. The strike mechanism may be out of adjustment or worn. Most old clocks also have some play in the gears that move the hands, so getting a perfect strike on 12:00 every time is hard. A minute either side is normal. Several minutes out means it needs servicing.

Most clocks can be turned back, provided they aren’t within about 10 minutes of striking and you don’t go back past 12:00 (or past 12:00 and 6:00 if the clock strikes the half hour). Many newer clocks have setback movements that can go back past those points, but even then most American clocks will strike the wrong number of times. Most clocks made before about 1885 will be damaged if you turn them back past a strike point. Clocks that don’t strike can be set backward freely. Unless the label inside the clock, or your clock repairer, says it’s a setback model, assume it isn’t.

On many clocks the simplest way is to not wind the strike side, which is usually the left one. Be aware that if you wind it again later, a count wheel clock may strike out of step with the time. Some clocks, especially those with a rack and snail strike, won’t run at all if the strike side isn’t wound. Metal hammers can often be replaced with leather-faced ones for a softer tone, and a stick-on felt pad over the hammer face sometimes helps. A clock repairer can also make a small hook that holds the hammer back when you don’t want the clock to strike.

Maybe. Badly worn parts, especially the escape wheel pivots and related parts of the escapement (the part that ticks), make a clock noisy. Replacing them and adjusting the escapement properly often makes a big difference. Some clocks are just louder than others and refuse to be quietened. Standing the clock on a rubber mat or moving it to another spot or room can also help.

Oil, cleaning and servicing

Clock oil, and nothing else. If the maker specified a particular oil, follow that where you can. A good clock oil stays where it’s put, resists drying out, doesn’t thicken in the cold or thin out in the heat, reduces friction and wear, and lasts several years. Mainsprings need a heavier oil or a light grease.

WD-40 and similar penetrating sprays are not suitable, even when the manufacturer recommends them. Neither are oils meant for car engines, guns, bicycles, sewing machines, door hinges or the all-in-one household oils. Some of these have some of the right qualities, but none has all of them. We only use imported clock oil in our workshop.

There’s no fixed timetable. It depends on the clock’s design, where it stands and what oil was used last time. Even experienced clock repairers disagree about it. As a rough guide, a full strip, clean and oil every 5 to 10 years suits many clocks, with a light re-oil in between if the clock needs it. If a clock that used to run well starts losing time, strikes slowly or stops before it has run down, it’s probably due for oiling and cleaning.

A dirty or badly worn clock should be serviced before it’s oiled, not just oiled. Don’t over-oil either, because extra oil only attracts dust. Proper oiling usually means taking the movement out of the case, so leave it to a qualified clock repairer. If you want to oil a clock yourself, call us and we’ll tell you what to use.

 

The only proper way to clean a movement is to take it completely apart and clean every part on its own. That takes a lot of time, but it lets us inspect the pivots and other parts and repair or replace them before bigger problems develop. A proper clean is a large part of a quality repair.

Cheaper operators cut corners. Some dunk the whole movement in solvent, add plenty of oil and hope it keeps running. You get what you pay for.

A dirty or badly worn clock should be serviced before it’s oiled, not just oiled. Don’t over-oil either, because extra oil only attracts dust. Proper oiling usually means taking the movement out of the case, so leave it to a qualified clock repairer. If you want to oil a clock yourself, call us and we’ll tell you what to use.

 

Cases, movements and conversions

Yes, probably. But think about it first. Whenever something original on an old clock is replaced or redone, its market value usually drops. If the finish is so poor that the clock looks bad, refinishing may be worth considering. Often a good clean and a coat of wax is the better choice. If you do refinish, you can use a modern durable finish or try to match the original method. Every clock is different and the decision is yours. A 150-year-old clock is allowed to look 150 years old.

The most common cause is that the strike side wasn’t wound, or wasn’t wound fully. Worn parts, poor lubrication and bad adjustment can also stop the strike from running or stop it from stopping. Getting it back in step depends on the clock, so call us if you’d like help. If it keeps going out of step for no obvious reason, the clock needs servicing.

Yes. Battery-powered quartz movements that strike the hours, or play Westminster chimes on the quarter hour, are available for many old wind-up clocks. Keep in mind that this changes something original and may reduce the clock’s value. Keep the original movement and pass it on with the clock.

It depends on the type and age of the clock, what you plan to do with it, the cost and whether a suitable replacement movement exists. Replacing original parts with new ones will significantly reduce the value of a collectable or antique clock. If the clock is more than 70 years old, or you want to keep it in the family, then keep the original movement and have it repaired or rebuilt wherever that’s possible.

Replacement does make sense if the clock has no movement, if the movement is damaged beyond repair, or if someone has already fitted the wrong one. For collectors the best option is to find an identical old movement and have it rebuilt before it goes in. A temporary battery quartz movement lets you enjoy the clock while you look for the right one.

Yes to the first. Wooden movements are very repairable, though the materials and methods are different and the cost can be significantly higher than for a standard brass movement. As for fragility, most wooden movement clocks are at least 175 years old and plenty are still running, which says a lot about how durable they are. Some collectors think old clocks should be preserved and never run. We believe clocks were made to run and be enjoyed. Several wooden movement clocks in our collection run every day.

Almost never. Wooden pivot holes need no oil. In most wooden clocks the escape wheel has one brass pivot hole, which can take a very small amount of oil every 3 to 5 years if needed, and the pallet strip (verge) can be oiled sparingly where it sits on its metal pin. If the movement has brass bushings, which were fitted later and aren’t a good idea, those need oil like any brass clock. Some shops use graphite powder on wooden pivot holes. Whether it helps is debatable, but it certainly makes the wood look worse. Most professionals recommend no lubrication on wooden parts.

Cuckoo
clocks

Sometimes. It’s said that almost every home has a cuckoo clock and almost none of them run. One reason is that many repair shops won’t touch them. Most clocks have a movement that comes out of the case in one piece and can be set up on a test stand. A cuckoo can’t. The whistles, bird, bellows and other parts are fixed to the case, the clock can’t run outside it, and many parts are hard to reach. Many were also mass-produced and not well designed. Often only the front of the movement is fixed to the case, so when the heavy weights are hung on, the movement can twist enough to stop the clock even though it looks perfectly normal.

We look at cuckoo clocks case by case and take them in when we think they can be repaired at a reasonable cost.

WD-40 and similar penetrating sprays are not suitable, even when the manufacturer recommends them. Neither are oils meant for car engines, guns, bicycles, sewing machines, door hinges or the all-in-one household oils. Some of these have some of the right qualities, but none has all of them. We only use imported clock oil in our workshop.

Sorry, we don’t do clock appraisals, and we can’t give a ballpark figure without having the clock in the workshop for inspection. Here’s why it’s so hard.

A clock’s price on the day depends a lot on where it’s sold. A clock offered at R10 000 in a good antique shop might fetch less than R3 000 at an online auction, depending on who is bidding at that moment. There are also different kinds of value: what you might get if you sold it, what it would cost to replace for insurance, and what it means to you. Your grandmother’s wedding present may be priceless to you and just another clock to an online bidder.

Provenance, meaning the history of the clock and who owned it, can add value for a collector. Condition matters even more, especially how much of the clock is original. Two clocks of the same make, model and age can be worth very different amounts. It’s often hard to tell what’s original. A 150-year-old clock may have had its hands, pendulum or movement replaced a century ago, and the replacement can look old without being original. A clock that runs and looks nice isn’t necessarily in good condition, and a carefully refinished clock would often have been worth more with its old finish left alone. There are also fakes, reproductions and old cases fitted with cheap parts, and even experts can be fooled by a good copy.

A proper appraisal means an expert physically inspecting the clock and doing careful research, which takes time and costs money. It isn’t usually worth it for an ordinary clock. Be wary of online appraisals from a photograph. Unless someone has actually examined the clock, don’t rely on them, especially if you think it may be rare or valuable.

To get a general idea, search online auction listings and antique dealers’ websites for similar clocks. Remember that asking prices are often well above what a clock actually sells for, and that two clocks that look identical in a photo can turn out to be quite different when examined.

Tic toc Doc | Clock Restoration Services Cape Town | Clock image

Still have a question about your clock? Call Bernard on 076 796 5555 or Nico on 081 580 0463.

Grandfather clock tips

How do I set up and set the time on a grandfather clock?

  • Make sure the clock is level and stable. Swing the pendulum. If the clock is straight and level, it should start with an even tick-tock.
  • Don’t put the clock where an air conditioner or heating vent will blow on the pendulum.
  • The pendulum should swing an equal distance either side of centre. If the clock leans one way you’ll hear TICK-tock, and if it leans the other way you’ll hear tick-TOCK. Adjust until both sound equally loud.
  • To set the time, move only the minute hand (the longer one) to the correct time. Don’t move the hour hand.
  • If the clock runs slow, raise the pendulum bob by turning the adjustment screw to the right. If it runs fast, lower the bob by turning the screw to the left.

Be patient. It takes time to get the timekeeping accurate.

My grandfather clock strikes the wrong number of hours. What can I do?

If the strike sequence is right but the number of strikes doesn’t match where the hands are pointing, it’s probably a count wheel clock and the count wheel needs resetting. Move the minute hand forward, a little at a time, and let the clock strike at each hour and half hour. Count the strikes and carry on until the number matches the hour shown by the hands. A single strike can be either the half hour or one o’clock, so you may need to work through a few half hours to be sure which one it is.

Never turn the hands back once you’ve passed the hour or half hour, because you may damage the clock. If you’re unsure, or it won’t come right, call us.